typically the fan cooling the heatbreak and extruder stays on even with the "extruder" aka part cooler fan turned off
another thing to note... klipper firmware takes the heavy processing typically handled by the printer control board, and offloads the burden onto the computer or device you have hooked up to the printer, processing and feeding the gcode one line at a time. so whatever device you are using needs to be up to the specs. I'm using an rpi 3b+ and have no issues.
klipper is the firmware flashed to the printer
gui is achieved and accessed through mainsail or octoprint. I haven't tried octoprint.
mainsail runs on a raspberry pi and can manage multiple klipper printers with one device. you can also add klipperscreen, it's an addon that can be used with a touchscreen for an interface at the printer (or anywhere really)...
but I just access mine running mainsail through my phone browser or the laptop I use to model and slice. I like orcaslicer because it integrates mainsail right into a tab in the slicer and provides a seamless user experience.
even better, add [screws_tilt_adjust] to take advantage of the crtouch and a little fancy computer math to make leveling super easy.
after configuring the screw locations and thread pitch, execute the command screws_tilt_calculate
https://www.klipper3d.org/Manual_Level.html
ender beds use M4 screws
I ran a couple temp towers with the overture petg and I found 270-275c nozzle/80c bed had the most desirable results. 0.6 nozzle 0.4 layer height. also with the sprite pro.
I printed a couple pretty pieces before I started to get burnt crusty bits showing up in my prints so take this with a grain of salt. maybe due to me changing layer height to 0.14 without further testing.
maybe they are talking about the helicopters you can drive around in too. they don't have big rotors on top, just basically a little fan in the front to cool the radiator when not in flight mode.
oh wait I'm thinking of a car
the caveat is that it had to once cost money? so stuff that has always been free is no longer available?
bruh I can't wait for this episode
I'm having a bad, bad, day
It's about time that I get my way
Streaming whatever I see
oh, indescribable me
I’m having a bad, bad, day
If you block my ad blocker that's not okay
Watch, this is so fun to see
oh, indescribable me
ℋ𝑜𝓂𝑒 𝒾𝓈 𝓌𝒽𝑒𝓇𝑒 𝓉𝒽𝑒 𝓉𝑒𝓇𝓂𝒾𝓃𝒶𝓁 𝒾𝓈
the only way to keep it clean is to remove one or two objects a day
source: my desk is a clusterfuck
good to know. I used the image button on the kbin post dialog.
also weight gain. I worked 6pm-6am for almost 2 years straight and gained 40lbs without changing my eating habits.
started drinking every morning after work too. and days (nights) off were a total clusterfuck. wake up, hit the grocery store before they close, start drinking because wtf else am I gonna do at 11pm alone in my camper with no wifi and spotty cell signal. my experience is probably not the norm lol
wouldn't of
hi, "wouldn't of" is improper. "wouldn't have" is the correct phrase to use. if you had not posted this, I would not of anyone to correct.
beep boop
I'm not a bot I'm just fucking with you
my grandfather had alzheimer's. dying from a side effect would have been better than the last 2 years of his life
I too used to be bogged down with one handle everywhere I went. but then I saw the light. I saw the truth. look at my username; it is gibberish! does that stop me? no, it only gives me power! my strength lies in the words I post, not the name under which they are posted. I might delete this account and make a new one under the first thing that pops into my head... in doing so I would lose nothing, and gain the world.
free yourself from your prison. creativity is liberty.
idk it usually sounds like this https://www.myinstants.com/en/instant/windows-31-startup-tada/
I played so much Metal Gear Acid. when you get your deck tweaked just right and start cranking out the perfect combos it was so satisfying
I visited 196 without posting anything